DEAERATORS
EXPLAINED
HANDBOOK
Second Edition, 2025
Join our newsletter if you want free access to more
engineering PDFs like this one.
⚫ saVRee ltd, 71-75 Shelton Street, Covent Garden, WC2H 9JQ, London ⚫ www.saVRee.com ⚫
contact@savree.com
Copyright © 2025 by saVRee ltd | All rights reserved. This publication or any portion thereof
may not be reproduced or used in any manner whatsoever without the express written
permission of the publisher.v1e
Table of Contents
What are deaerators? ............................................................................................................... 1
The Deaeration Process............................................................................................................ 1
Why remove oxygen and carbon dioxide? ............................................................................. 2
What is corrosion? ..................................................................................................................... 2
Deaerator System ...................................................................................................................... 3
Deaerator Components ............................................................................................................ 5
How Deaerators Work .............................................................................................................. 6
How Tray Deaerators Work ...................................................................................................... 7
Spray Scrubber Deaerator ....................................................................................................... 9
How Spray Scrubber Deaerators Work .................................................................................. 9
Design Considerations ............................................................................................................ 10
Steam System Comparison .................................................................................................... 10
Deaerator Entry Point ......................................................................................................... 10
Large Condensate Returns ................................................................................................. 10
Feedwater Tank Size ............................................................................................................ 11
Feedwater Tank Location ................................................................................................... 11
Maintenance............................................................................................................................. 12
www.saVRee.com Deaerators Explained| pg. 1
What are deaerators?
Deaerators are pressurised feedwater tanks also referred to as open feedwater
heaters. Deaerators are critical components of many steam systems and have several
functions:
•
Remove non-condensable gases from boiler feedwater.
•
Increase the temperature of makeup water as it enters the system.
•
Increase the temperature of condensate prior to it entering the boiler.
•
Provide a storage capacity of treated feedwater.
There are two common deaerator designs, the spray type and tray type (also known as
the spray-tray type). A variation of the spray type is the spray-scrubber type.
Deaerator
All medium to large steam systems require a deaerator to reduce the levels of dissolved
oxygen (O2) and carbon dioxide (CO2) in the boiler feedwater, both of which will cause
corrosion to boiler system components if not removed.
Deaerators achieve deaeration by raising the temperature of the feedwater, which
reduces the solubility of the non-condensable gases i.e. the gases are released from the
water. Once the dissolved gases have been released, the likelihood of corrosion is
drastically reduced and the feedwater can be fed to the boiler.
The Deaeration Process
The process of deaeration may occur mechanically or chemically. Deaerators provide
the mechanical solution whilst chemicals provide the chemical solution.
www.saVRee.com Deaerators Explained| pg. 2
A typical deaerator will remove almost all dissolved oxygen and CO2, with the remainder
being removed by oxygen scavengers (sodium sulphite, hydrazine etc.) and CO2
scavengers (neutralising amines, bicarbonate etc.).
Most deaerators are designed to reduce dissolved oxygen levels to 0.05 cc/l (7 ppb), with
oxygen scavengers removing the remainder.
Why remove oxygen and carbon dioxide?
Corrosion of boiler components exposed to water will occur if dissolved oxygen is
present, or, the water pH is low.
Boilers and their ancillary systems are mostly constructed of carbon steel. As steel is iron
based and oxygen reacts with iron to form red iron oxide (rust), the potential for
corrosion is high. For this reason, it is imperative that the boiler feedwater dissolved
oxygen content is as low as possible.
The amount of dissolved carbon dioxide in water dictates how acidic the water is. The
greater the dissolved CO2 in the water, the lower the water’s pH i.e. the more acidic the
water is. Low pH values will cause corrosion of boiler parts and consequently must be
avoided. A typical boiler will operate with a pH value of between 8 to 11 (approx.), but
this depends heavily upon the boiler system.
The corrosion rate is not only dependent upon the dissolved oxygen and dissolved
carbon dioxide levels, it is also dependent upon temperature. High temperatures cause
high corrosion rates, even with low amounts of dissolved gases. For this reason, low
temperature steam systems can tolerate much higher levels of dissolved oxygen and
carbon dioxide than high temperature systems.
What is corrosion?
Corrosion can be classed as general, localised, or stress.
General corrosion occurs within a single system component, or throughout the entire
system, and is usually considered light corrosion. A thin red oxide layer covering the water
side heat transfer surfaces of a boiler is an example of general corrosion. General
corrosion is often red (iron oxide) or black (magnetite oxide) in colour. If waterside
metal surfaces are red, the metal is corroding, and corrective action must be taken. Black
surfaces are desired as magnetite oxide deters further corrosion.
Localised corrosion relates to corrosion within a speci�c area; this type of corrosion is
usually moderate to extensive. Oxygen pitting (small holes in a metal surface caused by
www.saVRee.com Deaerators Explained| pg. 3
corrosion) is an example of localised corrosion. Oxygen pitting often occurs wherever the
water and steam phases meet (waterline in boiler or deaerator), or under sediment that
has settled somewhere in the system.
Stress corrosion occurs in high stress point areas. High chloride levels, thermal shock
and high pH, can all cause stress corrosion. Stress corrosion caused by high pH levels is
referred to as caustic embrittlement. Stress corrosion caused by thermal shock is
referred to as fatigue corrosion.
Deaerator System
Boilers generate steam which is delivered to the process. Some of the steam transfers its
energy to the process and condenses; the resultant water is termed condensate.
Condensate is gathered throughout the steam system and is returned to a central storage
tank, this is either an atmospheric feedwater tank, or a pressurised feedwater tank
(deaerator).
Spray Deaerator
Makeup water replaces water losses within the system. Water losses may be an
unavoidable part of the process e.g. steam cleaning of glass bottles in the edible food
industry, or, may be due to leaks or evaporation losses etc.
When condensate reaches the feedwater tank, it is termed feedwater, as it is then fed to
the boiler. Similarly, when makeup water enters the feedwater tank, it is thereafter
termed feedwater.
www.saVRee.com Deaerators Explained| pg. 4
Systems with low condensate returns must continually add large amounts of makeup
water. Continuously adding makeup water introduces more untreated water to the
system compared to when reusing condensate that has already been treated. For these
reasons, a deaerator is much more likely to be installed on a system with low condensate
returns than one with high condensate returns. It should be noted that systems with low
condensate returns will have larger operating costs due to higher water consumption,
higher heat/energy consumption (water has to be heated before entering the boiler) and
higher chemical treatment consumption.
The solubility of dissolved gases in water reduces as the temperature of the water
increases. In order to raise the boiler feedwater temperature, low pressure steam is
supplied. The steam transfers its heat to the feedwater until the feedwater approaches
its saturation point (boiling point). As the water approaches its saturation point, the
dissolved oxygen level approaches zero. In power plant, the steam supplied is often
waste steam from the steam turbine(s).
Gas Solubility Reduces as Temperature Increases
Dissolved gases released by the deaeration process are vented to atmosphere along with
trace amounts of steam. A typical vent will use a plate with an ori�ce (hole) to control the
rate at which gas is vented. If the ori�ce is too large, steam will be vented, which reduces
the overall plant e�ciency (because of the reduction in steam cycle e�ciency) and drives
up costs. If the ori�ce is too small, some gases may return to the feedwater, which is also
undesirable.
www.saVRee.com Deaerators Explained| pg. 5
Chemical dosing occurs on the makeup inlet line, within the deaerator, or between the
deaerator and boiler. The chemicals needed, their quantity, and where dosing should
occur, depend upon the system design. For example, makeup water supplied from a
reverse osmosis (RO) plant will have a low pH and should be treated before it enters the
deaerator.
Good to know – if you want to learn more about power engineering topics, be sure to
check our Power Engineering Fundamentals Video Course. You can also get access to
downloadable engineering PDF’s (like this one) and handbooks by joining our
newsletter.
Deaerator Components
A deaerator is an un�red pressure vessel. Deaerators are typically manufactured from
carbon steel, although some industries -such as the pharmaceutical industry- use
stainless steel. The pressure vessel is cylindrical in shape with as few welds and
penetrations as possible.
Attached to the deaerator are connections to the various systems it serves and other
appendages required to operate the deaerator. Common deaerator system connections
and appendages include:
•
Low pressure steam inlet.
•
Makeup water inlet.
•
Condensate inlet.
•
Feedwater outlet.
•
Safety relief valve (SRV).
•
Water column or siphon.
•
Level sight glass.
•
Level control sensor.
•
Drain line (for maintenance).
•
Over�ow pipe (non-return design).
•
Chemical injection point.
•
Flanges for gauges (pressure and temperature gauges etc.).
www.saVRee.com Deaerators Explained| pg. 6
Tray Deaerator Connections
A pressurized deaerator will operate at approximately 5 psi at 230°F (imperial), or 0.4
bar at 105°C (metric). Deaerator feedwater will be maintained as close to the saturation
temperature as possible in order to reduce the level of dissolved gases as much as
possible, but without the water changing phase to steam. If the feedwater exceeds its
saturation temperature, it will begin to form steam and will either condense, or be vented
to atmosphere, both of which are not desired.
How Deaerators Work
There are two common deaerator designs, spray and tray (spray-tray). Each design has
its own operating characteristics. Regardless of the design employed, both deaerators
designs:
•
Maximize the contact surface area between the water and steam to obtain a
high heat transfer rate.
•
Rely upon direct contact between the steam and water (usually tray, spray,
bubbling, or a combination of these).
•
Employ spray nozzles.
•
Utilize steam as the heat source.
•
Agitate the water using steam.
•
Can be mounted onto the top of a feedwater storage tank.
•
Are often manufactured from the same materials.
•
Are open/vented to atmosphere.
www.saVRee.com Deaerators Explained| pg. 7
Although spray deaerators are often mounted to the top of feedwater tanks, they can
also be installed within the feedwater tank. A deaerator mounted above a feedwater tank
will appear either as a small tank connected by a pipe to the feedwater tank, or, as a
dome or vertical column, mounted directly to the feedwater tank.
Makeup water will pass through the deaerator when it enters the system. Condensate
may or may not pass through the deaerator depending upon its condition when returned
to the feedwater tank. Deaerator designs vary because each steam system has unique
requirements.
How Tray Deaerators Work
Water enters the deaerator and �lls the water box. The water box is a temporary holding
area that ensures water is fed evenly through a series of spray nozzles, then into the
deaerator.
Each spray nozzle acts as a non-return valve and will close if the water box has insu�cient
water pressure. To ensure long life, spray nozzles, the surrounding spray area and the
trays, are all constructed of stainless steel.
Spray Tray Deaerator
Once the water has passed through the spray nozzles, it comes into direct contact with
the steam. The steam �ows in a counter direction to the water. As the steam heats the
water, the dissolved gases are liberated. The quantity of dissolved gases present reduces
www.saVRee.com Deaerators Explained| pg. 8
as the water cascades down through each successive tray. The upper trays are referred
to as heating trays, or �rst stage trays. The lower trays are referred to as deaeration
trays, or second stage trays. The water then exits the tray area and is discharged to the
feedwater tank.
Dissolved gases and some steam are constantly discharged through the vent. A typical
deaerator will vent between 5% to 15% of the steam that passes through the deaerator.
As steam costs money to generate, it is bene�cial to vent as little steam as possible.
Approximately 90% to 95% of deaeration occurs within the spray area with much of the
remainder occurring in the tray area. Mechanically deaerated water is usually designed
to lower the oxygen content to 7 parts per billion (ppb). Any remaining oxygen in the
feedwater is stripped using oxygen scavenging chemicals (sodium sulphite, hydrazine
etc.).
How Spray Deaerators Work
Condensate and makeup water enter the water box directly above the spray nozzles; the
spray nozzles are spring loaded. Water pressure causes the nozzles to open and water is
sprayed into the deaerator. Spraying the water into the deaerator ensures a large contact
surface area between the water and steam, which ensures good heat transfer between
the two �uids (�uids are de�ned as either liquid or gas).